Heat transfer lab manual

Compare laboratory balances from several brands according to their weighing capacity and calibration type.

Heat transfer lab manual

To determine the thermal conductivity of a metallic rod. To determine the thermal conductivity of an insulating power. To determine the thermal conductivity of a solid by the guarded hot plate method.

Heat transfer lab manual

To find the effectiveness of a pin fin in a rectangular duct natural convective condition and plot temperature distribution along its length.

To find the effectiveness of a pin fin in a rectangular duct under forced convective and plot temperature distribution along its length. To determine the surface heat transfer coefficient for a heated vertical tube under natural convection and plot the variation of local heat transfer coefficient along the length of the tube.

Also compare the results with those of the correlation. Also compare the results with those of the correlations. To measure the emmisivity of the gray body plate at different temperature and plot the variation of emmisivity with surface temperature.

To find overall heat transfer coefficient and effectiveness of a heat exchange under parallel and counter flow conditions. Also plot the temperature distribution in both the cases along the length of heat of heat exchanger. To verify the Stefen-Boltzmann constant for thermal radiation.

To demonstrate the super thermal conducting heat pipe and compare its working with that of the best conductor i. Also plot temperature variation along the length with time or three pipes. To study the two phases heat transfer unit. To determine the water side overall heat transfer coefficient on a cross-flow heat exchanger.

Design of Heat exchanger using CAD and verification using thermal analysis package eg. At least ten experiments are to be performed in the semester. At least seven experiments should be performed from the above list.

Voltmeter, Ammeter, Stop watch, Copper — constantan thermocouple, Power supply, Heating element, Digital temperature indicator and Voltage regulator. Thermal conductivity is an important thermo - physical property of conducting materials, by virtue of which the material conducts the heat energy through it.

The thermal conductivity for a given material depends on its state and it varies with direction, structure, humidity, pressure and temperature change.

Thermal energy can be transported in solids by two means. Transport of free electrons. Thus in hotter portion of the solid, the atoms which have larger vibration energy, transfer a part of its energy to the neighboring low energy molecules and so on throughout the whole length of the body.

The metal rod of brass is inserted into hole so that when power supplied to heater, heat transfer will take place from the base to another end.

Heat transfer lab manual

The power supply to heat may be adjusted to desire quantity by means of electronic controlled circuit for that one rotary switch is provided on the control panel. Electric power input can be measured by using digital voltmeter and ammeter multiplier.

Thermal Conductivity of Rod Procedure: Switch on the power supply and adjust voltage and current so as to allow some watts input to heater coil. Wait for steady state.

Used Lab Equipment | Biodirect Pre-Owned Lab Equipment

Steady state can be observed by the temperature reading at one or all points on the surface of the metal rod. Steady state is reached when these temperatures stop changing with time.

Under steady state conditions note the temperature of each point on the surface of the rod as well as temperature of surrounding. Repeat above procedure for several power input.Tips for sublimation printing using Astex Heat Transfer Machines, Wasatch Softrip Software and Epson Large Format Printers with Sawgrass Sublimation Inks.

The Engineering Laboratory promotes U.S. innovation and industrial competitiveness by advancing measurement science, standards, and technology for engineered systems in ways that enhance economic security and improve quality of life. Heat & Mass Transfer Lab Manual Version February Prepared by: Reviewed by: Ms.

Sushma S Mr. Faheem Akthar HEAT & MASS TRANSFER LAB Dept.

B. Software

Of Mechanical Engg, CIT, Gubbi 8 COMPOSITE WALL APPARATUS AIM: To determine the overall heat transfer coefficient of a composite wall. We offer analytical balances from manufacturers including AND Weighing, Sartorius, Mettler Toledo, Ohaus, Acculab, Scientech and Adam ashio-midori.come laboratory balances from several brands according to their weighing capacity and calibration type.

Save a bundle on analytical scales that offer external calibration versus internal. Download HT Laboratory Notes. For now on this particular page we have provided Heat Transfer lab manual or lab handbook in pdf for JNTUH JNTUK or JNTUA Students of ashio-midori.com Software Availability.

All software and a manual (Heat Transfer Tools) consisting of about pages of documentation were originally published by McGraw-Hill in July In addition to the software, the CD-Rom includes about 60 additional pages in "pdf" files detailing the numerical modeling used "behind the scenes," making these materials very appropriate for use at the graduate level as.

Commerical Plate Heat Exchanger and press assemblies.